Pipeline & Piling Services Company Limited
Switch to English
Switch to Thai
  i) Onshore   ii) Subsea Pipelines   iii) Jacket & Platforms   iv) Seabed Stabilization   v) FPSO

Quick Links :
ANT Solution NEW
Neptune Research, Inc. NEW
Cape Holland
NDT Services
Seabed Systems
Subsea Innovation
PAPS ISO9001 Certification
IMCA, the International Marine Contractors Association

Kamos Gaskets
Kamos Gaskets for Sale from PAPS

Kamos Gaskets for Sale from PAPS Over the past few years there have been several cases of near-accidents due to leaks in flanges. Experience from offshore operation has shown that flanged connections in piping at high pressure in the presence of hydrocarbons constitute a large safety risk.

Better methods of avoiding leaks from such flanges will therefore provide a safety benefit, at the same time more effective methods of leak testing can reduce the down-time connected with testing, and thus reduce the loss in earnings as the result of downed production.

KaMOS® is now introducing a new method of leak testing of flanges with ring joints that can measure whether tightness has been achieved on all sealing surfaces of flange before the flange and pipe are subjected to internal pressure, as well as monitor the flange connections for future leakages.

The method permits flange integrity to be tested from the outside before system pressure is applied.
In the safety equation this will offer great benefits. It will also in many cases reduce the test time for normal pressure and leak tests because certain repetitions of the tests in case of leaky flanges would be avoided.

The test method is based on pressurizing the annular space above and below the seal ring using test gas. If no pressure loss is recorded during this pressurization, the seal is deemed tight.

The test gas that is applied to the annular space is applied using simple portable equipment, consisting of a gas reservoir, a manometer and hoses.

The equipment is easy to handle and will make it possible to test flanges on a one-off basis without pressurizing entire systems.

The test system will also check the primary and secondary sides of the seal for tightness.

The leak testing that is used today cannot distinguish these two sides, only if it’s tight or not.

KaMOS® RTJ gasket KaMOS® RTJ gasket
KaMOS® Kammprofil gasket KaMOS® Kammprofil gasket
KaMOS® Blind gasket - with pressure gauge KaMOS® Blind gasket - with pressure gauge
KaMOS® Nitrogen Test Equipment (type 200500) test range 0-200 bar KaMOS® Nitrogen Test Equipment (type 200500) test range 0-200 bar
KaMOS® Hydraulic Test Equipment (type 200800) test range 0-400 bar KaMOS® Hydraulic Test Equipment (type 200800) test range 0-400 bar
Please Contact Us for a complete list of available sales equipment.

Also available:

BISEP Isolation Tools, Bolt Tensioning Tools, Bolt Torquing Tools, Electric and Diesel Motors, Epoxy Sleeves, Flange Splitters, Flange Testers, Hot Tap Tools & Clamps, Hydraulic Hose Winches, Hydraulic Shackles, Impact Hammers (used), Internal Lifting Tools, Joint Testers, Kamos Actuators, Kamos Gaskets, Mass Flow Excavators, Nut Splitters, Pipe Cutting Tools, Pipe Handling Tools, Pipe Plugs (Oil & Gas Industry), Pipe Wrap both Subsea & Above Water, Pipeline Clamps, Pipeline Connectors, Pipeline Engineering, Pipeline Inspection Tools, Pipeline Isolation Tools, Reconditioned Pumps, Remotely Operated Isolation Plugs, Tethered Isolation Plugs, Valves, Vibratory Hammers (new), Vibratory Hammers (used), Weightcoat & Coating Removal Tools, Weld Testers.
Paps Thailand
Paps Thailand
Paps Thailand
Paps Thailand
Paps Thailand
Paps Thailand
Paps Thailand
Paps Thailand
Copyright © 2018 : PAPS-THAILAND.COM : All Rights Reserved
Web Design, Web Hosting, Web Marketing - ThaiWebpro.com
Site developed by : www.thaiwebpro.com